Truck & Bus Forum

Truck & Bus Forum (https://www.truckandbusforum.com/index.php)
-   Utility Service Vehicles & Others (https://www.truckandbusforum.com/forumdisplay.php?f=20)
-   -   Two Volvo L90's moving a railway switch (Video) (https://www.truckandbusforum.com/showthread.php?t=3943)

Bobjork 8th November 2011 17:42

Two Volvo L90's moving a railway switch (Video)
 
http://www.youtube.com/watch?v=tjmsueaGHcs
Two Volvo L90s today at the railway training centre.

First removing old sleepers from the trackbed.
Then moving the point/switch into place so we can mount it.
Last in the movie, a Bobcat running on rails. :D

Wanted to upload this to the TV section but couldn't find any category for it.

coastie 8th November 2011 18:09

It's a good job they're 4wd!! A tad more ballast on the r send I feel!:)

Thankyou for posting it though.

Bobjork 8th November 2011 18:15

Quote:

Originally Posted by coastie (Post 11457)
It's a good job they're 4wd!! A tad more ballast on the r send I feel!:)

Thankyou for posting it though.

Where do you want more ballast?

We are going to put some ballast in the switch when it is mounted. The grass is in ballast (and coal).
The switch will not be used by trains, it is only for display and for practicing measuring etc.

G-CPTN 8th November 2011 18:25

I cannot imagine our H&S allowing that!

Machines with greater lifting capacity would be required . . .

Thanks for sharing.

After spending time earlier today researching Scania L-types I was expecting to see vintage bonneted trucks!

Bobjork 8th November 2011 18:29

Quote:

Originally Posted by G-CPTN (Post 11459)
I cannot imagine our H&S allowing that!

Machines with greater lifting capacity would be required . . .

Thanks for sharing.

After spending time earlier today researching Scania L-types I was expecting to see vintage bonneted trucks!

Yes, greater loading capacity would be nice. But they would also be bigger and it was tight on some places. (One of the loaders dented the wall of one of the sheds).

No old trucks here :) We also got a visit from a Scania with two loads of ballast. But I was busy doing other works so no pic of that one.

G-CPTN 8th November 2011 18:49

Ballast can be either Track Ballast:- http://en.wikipedia.org/wiki/Track_ballast

or Ballast Weights added to counterbalance or increase weight up to a prescribed minimum.

Bobjork 8th November 2011 19:26

Quote:

Originally Posted by G-CPTN (Post 11461)
Ballast can be either Track Ballast:- http://en.wikipedia.org/wiki/Track_ballast

or Ballast Weights added to counterbalance or increase weight up to a prescribed minimum.

Aha. I knew that ballast could be that as well... but I did not think of it in this case :)
But "r send"?

G-CPTN 8th November 2011 19:52

r send = ar_se end (back end) / rear.

Bobjork 8th November 2011 19:55

Aha, like arsenal :)
Too advanced for me right now. Tired after a day of digging.

G-CPTN 8th November 2011 20:02

Quote:

the British/Irish-English vulgarism for the buttocks, equivalent to "ass" in American or Canadian English

"********," a similar British/Irish term for the anus, equivalent to "*******" in American or Canadian English
From:- http://en.wikipedia.org/wiki/****

(except that you have to replace the **** with the letters a_r_s_e - if you try to put that word here it 'bleeps' it out with astericks!)

I see that we aren't allowed a_rsehole or even a_sshole . . .

It is used in all but the most polite society to mean backside as in "Look at the a_rse on that lass/girl/woman."
or even "Get your a_rse down here!" meaning "Come here quickly!"


All times are GMT +1. The time now is 16:10.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.